logo
Langfang Yifang Plastic Co.,Ltd
이메일 sales@lfrfeng.net TEL : 86-0316-2605138
집
집
>
뉴스
>
회사 뉴스 Plastic Wall Plugs and Anchors by Substrate Type
이벤트
메시지를 남기세요

Plastic Wall Plugs and Anchors by Substrate Type

2026-11-19

최신품은 뉴스를 따릅니다 Plastic Wall Plugs and Anchors by Substrate Type

Most fixing failures we hear about are not product failures. The plug was sound, and it was simply chosen for a wall it was never designed for. Solid brick, perforated brick, aerated concrete and gypsum board each fail in a different way, so the anchor mechanism has to match the failure mode rather than the drill diameter.

The Substrate Comes Before the Anchor

European assessment guidance keeps plastic anchors for solid masonry in a separate document from anchors for hollow or perforated masonry, and the split exists for a physical reason. An expansion plug works by pressing outward against material that can resist that pressure. Put the same plug into a hollow block and there is nothing to press against, so it holds on friction alone and the figure printed on the box stops meaning anything. Aerated concrete fails a third way, by crushing around the hole, because it is weak in compression rather than short of thickness. Gypsum board fails a fourth way, through the paper face, which is why board fixings spread their load behind the sheet instead of inside it.

Four Substrates, Four Mechanisms

The failure mode differs because the material around the hole differs. That is the whole reason a single plug family cannot cover a mixed development.

SubstrateMechanism that worksHow the fixing fails
Solid masonry and concreteExpansion plug, or a screw-in anchor with a coarse threadPull-out, usually because the drilled hole was oversized for the plug
Hollow or perforated masonryToggle or butterfly anchor, spreading behind the unitA wing tears through a thin web, or the plug spins loose in the cavity
Aerated concreteScrew-in anchor with a wide, deep threadCrushing around the hole, because the material is weak in compression
Gypsum board and drywallToggle bolt or hollow-wall anchor with a spreading legThe paper face tears and the fixing pulls straight through

Our own range keeps those families apart. The 8 x 40 mm expansion anchor with screw covers solid material, and the DIN 10 x 33 mm hollow wall anchor kit handles cavity walls. For board, the 13 x 30 mm gypsum anchor is the one to quote.

Reading a Load Figure Correctly

A published resistance is a characteristic value measured under defined conditions, not a working load. EOTA's guidance for solid masonry and the companion document for hollow and perforated masonry both work this way. The published figure belongs to a combination of anchor, substrate, hole tolerance and embedment depth, and changing any one of them changes the number. Working load follows from the characteristic value only after the safety factor your code requires has been applied.

One plug for every wall is the most expensive habit in the trade. It costs almost nothing per piece, and it produces a callback every time a hollow wall is treated as if it were solid. Distributors feel this twice, once in returns and once in the labour the contractor will not pay for again.

We mould and supply the plug, the anchor and the documentation that travels with them. The load case, the edge distance and the safety factor belong to the engineer who signs the fixing. No catalogue should be asked to replace that calculation. Send us the substrate and the hole diameter, and we will quote the family that fits it. What we will not do is invent a resistance figure for a wall we have never seen.

FAQ

Is a longer plug always a stronger one?
Not by itself. Length has to reach sound material or spread behind the board, and extra length inside a cavity only adds cost.

Does aerated concrete need a different plug?
Yes. Aerated concrete is weak in compression, so it takes a screw-in anchor with a wide thread rather than an expansion plug.

Can the material be colour matched?
Yes. Nylon and PE plugs are moulded to colour references, including Pantone numbers.


Langfang Yifang Plastic Co., Ltd moulds wall plugs and anchors in Langfang, Hebei, across expansion, hollow-wall, toggle and screw-in families. The range is listed under plastic wall plugs and anchors, and heavier facade fixings sit outside general trade supply. For the trade-level view of the same family, see plastic expansion anchors in construction.

언제든지 우리와 연락하세요

86-0316-2605138
중국 허베이성 랑팡시 다청현 황덕산업구
직접적으로 당신의 조사를 우리에게 보내세요